Home → Paint's Blog

Paint's Blog

Removing Paint Using Paint Remover

by Andre Ong
Removing Paint Using Paint Remover

Before you start painting a wall or any other surface like wood for example, you need to make sure that the surface is even and clean of dirt.  There are different techniques to achieve this and this article describes the various methods that can be used to remove paint effectively, before you start a paint job
      • Scraping is the traditional technique used to remove paint from walls. All you need is a putty knife or plastic scraper. When selecting a scraping tool just ensure that it is rigid enough to withstand the wear and tear, especially when working on large interior walls. Drop a cloth on the floor to cover the scrape dust and start with the flat edge of the scraper to peel off paint from the wall.
      Removing Paint Using Paint Remover
      • Wire brush is another tool that can be used to loosen old paint from the wall. Start using the wire brush in a vertical or oscillating movement and finish off the surface with sand paper. You can use a vacuum cleaner to remove fine dust from the surface.
      • Heating the surface is a good idea to remove paint that refuses to budge. Sometimes you can be left with certain areas that do not peel off easily. Use a hot air blower on the area where you want the paint to be removed. Once some bubbles are formed, use a metal scraper to quickly remove the paint. This process has to be used only on left over areas (where the paint is still sticking to the wall) as this is a tedious process for longer areas.
      • Sanding is another technique that can be used to dislodge paint from hard to reach areas. If the working area is large, it is best to use a power tool like an orbital power sander to sand out paint.Removing Paint Using Paint Remover
      • Paint stripping gels are widely used chemical stripping agents and have found to be very successful in removing large areas of paint that are not easy to remove with a scraping or sanding process. Apply a paint stripper over the wall with a brush and cover the entire wall with a layer of the gel. After a few minutes (refer manufacturer’s instructions for exact time), you can remove the paint with a scraper.
      Once the paint removal is done, remember to wipe the wall with a wet sponge and let it dry before starting the paint job. Removing Paint Using Paint Remover

      You Have Been Using a Paint Roller Wrongly All This Time

      by Andre Ong
      You Have Been Using a Paint Roller Wrongly All This Time

       

       We all know that the right equipment is essential for a good paint job. While tools are very important, the technique is equally important to achieve the best finish. Using a wrong technique or lack of knowledge on how an equipment should be operated can lead to bad results. When it comes to painting, the following paint roller tips will help you make a remarkable difference to the surface finish

      You have been using a paint roller wrongly all this time!

      • Buy a good quality roller that has a good roller pin and long handle to help you paint with ease. Having a good roller will solve most the ‘marking’ related problems that appear when you apply paint on a smooth wall.
      • Divide your paint area into the edges and the mid sections. Use a brush to apply paint at the edges and corners. Once this is done you are setup to cover the major portion of the wall with your roller
      • Leave a six inch gap from the edges and start the roller strokes. The strokes should go up and down in the form of a ‘W’. Spread the paint quickly in this motion. At this point of time don’t be too worried about the quality of the finish - it will look raw. This is your first coat with newly loaded paint.
      • Without taking a fresh dip of paint, re-work the area with a wet edge. A wet edge is important as it will ensure that there are no visible marks between two paint strokes. Don’t wait for long or pause in between two strokes as this will allow the painting edge to dry. So here’s the golden tip again – ‘Paint on wet edges’
      • Now for the finishing touch smooth out the paint strokes at the joining area (the edge of the wall and the roller application) with a horizontal stroke. The horizontal stroke will make sure that the patch up in this joining area is smooth. Also keep in mind that you need to do this without a paint reload which would mean that your roller is relatively dry when compared to a freshly loaded one.
      • Use a roller scraper to remove extra paint that might be sticking on the surface. Wash you roller with a mild detergent and keep it clean. You next paint job will be a lot easier as you will be have a soft roller ready to soak in paint.
      You have been using a paint roller wrongly all this time.

      Our brands